By Tarek, CraftsVinyl by Plotto
To use heat transfer vinyl, cut your design mirrored with the shiny side down and weed away the extra vinyl. Then press it onto fabric with an iron or heat press and peel the carrier sheet. It works the same in Cricut and Silhouette machines. The time, temperature and peel (hot or cold) come from the instructions supplied with your vinyl.
Iron-on vinyl, HTV and heat transfer vinyl are three names for the same thing. This page covers the basics and links to every iron-on guide we’ve written. New to cutting machines? Start with our Cricut beginner guide.
Iron-on vinyl instructions: how do I apply HTV step by step?
- Design and size it in centimetres in your machine’s software, such as Cricut Design Space or Silhouette Studio.
- Mirror the design. Iron-on vinyl is cut from the back, so the design must be flipped. If you forget, every word comes out backwards.
- Place the vinyl shiny side down on the mat. The shiny side is the clear carrier sheet.
- Choose the matching material setting and cut. Cut a 2 cm test square first on any new roll.
- Weed away everything that isn’t your design, leaving it on the carrier sheet.
- Pre-press the fabric for a few seconds to remove moisture and creases.
- Press with the carrier sheet facing up, following the time, temperature and pressure in your vinyl’s instructions.
- Peel the carrier hot or cold, as your vinyl’s instructions say. If an edge lifts, lay the carrier back down and press again.
Want the Cricut version with screenshots? See how to use iron-on vinyl with a Cricut.
Which type of heat transfer vinyl should I use?
| Type | Looks like | Best for | Watch out for |
|---|---|---|---|
| Smooth (standard) HTV | Matte or gloss, one solid colour | Names, slogans, school and work wear | The easiest place to start |
| Glitter HTV | Sparkly, slightly textured | Christmas tops, party T-shirts | Thicker, so it may need more cut pressure |
| Puff vinyl | Rises into a raised 3D finish when pressed | Statement jumpers and hoodies | Bold, simple fonts work best |
| Reflective HTV | Bright when light hits it | Kids’ coats, running and cycling kit | Test-cut first; it can be stiffer |
| Glow-in-the-dark HTV | Glows after time in the light | Halloween and kids’ pyjamas | Bigger shapes glow better than fine lines |
Shop the range in our iron-on vinyl category, including 3D puff vinyl.
Can I use an iron instead of a heat press?
Yes, for small designs. Use a hard, heat-safe surface rather than a padded ironing board, switch off any steam, and press firmly without sliding the iron. A heat press or mini heat press gives more even heat, which helps on larger designs and on glitter or puff vinyl.
How do I make iron-on vinyl last in the wash?
Follow the care instructions supplied with your vinyl. Most ask you to wait at least a day before the first wash, turn the item inside out, wash cool, and avoid ironing straight onto the design. If a design peels after washing, it usually wasn’t pressed long or firmly enough, or the fabric wasn’t pre-pressed.
Tip from our workbench: after pressing, before you peel, run your fingertip slowly along the thinnest letter. If you can feel the fabric weave through the carrier, the vinyl has bonded. If it feels like it’s floating on top, give it a few more seconds.
What are the most common iron-on vinyl mistakes?
| Mistake | Fix |
|---|---|
| Design comes out backwards | Switch Mirror on before cutting |
| Machine cuts through the carrier | Vinyl was shiny side up, or the pressure is too high: flip it and test again |
| Vinyl won’t weed | Not cut through: re-cut a test square with more pressure or a sharper blade |
| Edges lift after pressing | Press again with the carrier down, and pre-press the fabric next time |
| Glue marks round the design | Too much heat or pressure: check your vinyl’s instructions |
Iron-on vinyl guides and projects
- How to use iron-on vinyl with a Cricut
- Iron-on vinyl Christmas jumper with a Cricut
- Personalised Christmas stocking with iron-on vinyl and a Silhouette
- Iron-on vinyl Christmas pyjamas with a Cricut
- Cricut Design Space guide: mirroring, sizing and cutting
FAQ
Is heat transfer vinyl the same as iron-on vinyl? Yes. HTV, heat transfer vinyl and iron-on vinyl all mean vinyl with a heat-activated glue, made for fabric.
Which side of iron-on vinyl goes down on the mat? The shiny side, which is the clear carrier sheet. The duller, coloured side faces up so the blade cuts the vinyl and not the carrier.
What fabrics can I put iron-on vinyl on? Cotton, polyester and cotton-poly blends are the easiest. Check your vinyl’s instructions for anything heat-sensitive, such as nylon or very stretchy fabric.
Do I need to mirror iron-on vinyl? Yes, always, because you cut it from the back. Adhesive vinyl is the opposite and is never mirrored.
Free shipping all over the UK, with UK dispatch and free 14-day returns.
